DTP HDMI 330 4K Tx/Rx |
|
specification |
|
Frame rate1 | 24, 25, 30, 50, or 60 fps |
Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:0 |
Color bit depth1 | 8 bits per color |
Signal Type | HDMI 1.4, HDCP 2.3 |
Max. video data rate | 10.2 Gbps (3.4 Gbps per color) |
NOTE | 1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate. |
|
NOTE | This product consists of a transmitter (DTP HDMI 4K 330 Tx) and a receiver (DTP HDMI 4K 330 Rx), sold separately, with twisted pair cables linking the transmitter and receiver. |
|
NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
|
Video |
Maximum data rate | 10.2 Gbps (3.4 Gbps per color) |
Maximum pixel clock | 300 MHz |
Resolution range | Up to 2560x1600* @ 60 Hz or
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(* reduced blanking) |
Color bit depth | 8, 10, or 12 bits — subject to the maximum data rate limit |
Formats | RGB and YCbCr digital video |
Standards | DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E |
|
Video Input — transmitter |
Number/signal type | 1 single link HDMI (or DVI-D*) |
Connectors | 1 female HDMI type A |
|
Interconnection Between Transmitter and Receiver |
Connectors | 1 female RJ-45 per unit |
Termination standard | TIA/EIA T568B |
Signal transmission distance | |
1080p @ 60 Hz | Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
2560x1600 @ 60 Hz | Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
4K/UHD @ 30Hz and 60 Hz | Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
Cable requirements | Solid conductor, 24 AWG or better |
Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) |
NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
Video Output — receiver |
Number/signal type | 1 single link HDMI (or DVI-D*) |
Connectors | 1 female HDMI type A |
|
Audio |
Gain | Unbalanced output: 0 dB; balanced output +6 dB |
Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
THD + Noise | 0.03% @ 20 Hz to 20 kHz at maximum output |
S/N | >90 dB, at maximum output (15 dBu), balanced (unweighted) |
Stereo channel separation | >80 dB @ 1 kHz to 20 kHz |
|
Audio input |
Number/signal type | 1 PC level stereo, unbalanced |
NOTE | Analog audio is not embedded onto the digital video signal. Embedded digital audio is not de-embedded from the digital video signal. |
|
Connectors | (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) |
Impedance | >10k ohms, DC coupled |
Nominal level | -10 dBV (316 mVrms) |
Maximum level | +6 dBV (unbalanced) |
NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
Audio output |
Number/signal type | 1 stereo (2 channel), balanced/unbalanced |
Connectors | (1) 3.5 mm captive screw connector, 5 pole |
Impedance | 50 ohms unbalanced, 100 ohms balanced |
Gain error | ±0.1 dB channel to channel |
Maximum level (600 ohm) | >+11 dBu, balanced |
|
Communications — External Device (pass-through, unidirectional or bidirectional) |
Serial control port input/output | |
Transmitter | RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port) |
Receiver | 1 set of proprietary signals on a female RJ-45 jack |
Serial control port output/input | |
Transmitter | 1 set of proprietary signals on a female RJ-45 jack |
Receiver | RS-232 via a 3.5 mm, 3 pole captive screw connector |
Baud rate and protocol | 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity |
Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd |
IR control port | (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
IR control pin configuration | 3 = Gnd, 4 = IR Tx, 5 = IR Rx |
|
General |
Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
Power consumption | |
Transmitter | |
Device | 2.5 watts |
Device and power supply | 3.4 watts |
Remote power budget | 12 watts |
Receiver | |
Device | 4.2 watts |
Device and power supply | 5.8 watts |
Remote power budget | 12 watts |
NOTE | Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. |
|
Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling | Convection, no vents |
Thermal dissipation | |
Transmitter | |
Device | 7.4 BTU/hr |
Device and power supply | 10.4 BTU/hr |
Receiver | |
Device | 13.0 BTU/hr |
Device and power supply | 18.7 BTU/hr |
Mounting |
Rack mount | Yes, with optional 1U high rack shelf |
Furniture mount | Yes, with optional under-desk mounting kit |
Enclosure type | Metal |
Enclosure dimensions | |
Transmitter | 1.0" H x 4.3" W x 3.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors.) |
Receiver | 1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.) |
Product weight | |
Transmitter | 0.5 lbs (0.3 kg) |
Receiver | 1.0 lb (0.5 kg) |
Regulatory compliance | CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
Complies with the appropriate requirements of RoHS, WEEE
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply. |
NOTE | **CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable. |
|
Product warranty | 3 years parts and labor |
Everlast power supply warranty | 7 years parts and labor |
NOTE | All nominal levels are at ±10%. |
|
NOTE | Specifications are subject to change without notice. |
|
(5452-D19) |