| DTP3 R 201 |
|
 specification |
|---|
 |
| Frame rate1 | 24, 25, 30, 50, or 60 fps |
| Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:0 |
| Color bit depth1 | 8, 10, 12 bits per color |
| Signal Type | HDMI 2.0b, HDCP 2.3 |
| Max. video data rate | 18 Gbps (6 Gbps per color) |
| NOTE | 1Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. |
|
|
| Video |
|---|
| Maximum data rate | 18 Gbps (6 Gbps per color) |
| Maximum pixel clock | 600 MHz |
| Resolution range | Up to 1080p @ 120 Hz or 4K @ 60 Hz (4:4:4 subsampling)
5120x1080* @ 30 Hz, 5120x1440* @ 30 Hz, 5120x2160 @ 30 Hz,
5120x2560* @ 30 Hz,
5120x2880* @ 30 Hz |
| NOTE | *Indicated rates not available via standard 256-byte EDID and may require custom video card configuration. |
|
| Horizontal frequency range | 15 kHz to 270 kHz for resolutions up to 18 Gbps |
| Vertical frequency range | 24 Hz to 240 Hz for resolutions up to 18 Gbps |
| Color bit depth | 8, 10, or 12 bits — subject to the maximum data rate limit |
| Formats | RGB and YCbCr digital video |
| HDR | HDR10, HDR10+, Dolby Vision |
| Standard | DVI 1.0, HDMI 2.0b, HDCP 1.x, HDCP 2.3 |
| NOTE | Extron strongly recommends compatibility testing while designing, and before installing, any 3D system. There are several unique 3D formats in use by source devices and display manufacturers. The level of 3D product support is governed by pixel clock, signal format, and communication between source and sink devices. Please contact an Extron Applications Engineer for more information. |
|
|
| Video Input |
|---|
| Number/signal type | |
| DTP3 | 1 DTP3 |
| Connector | |
| DTP3 input | 1 female RJ-45 |
|
| Video Output |
|---|
| Number/signal type | 1 single link HDMI or DVI-D* |
| Connector | 1 female HDMI |
| NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
|
| Interconnection Between Transmitter and Receiver |
|---|
| Connector | 1 female RJ-45 per unit |
| Termination standard | TIA/EIA T568B |
| Signal Transmission Distance (using XTP DTP 24 cable) | |
| 1080p @ 60 Hz | Up to 330' (100 m) using shielded twisted pair STP or XTP DTP 24 cable |
| 4K/UHD @ 30 Hz | Up to 330' (100 m) using shielded twisted pair STP or XTP DTP 24 cable |
| 4K/UHD@ 60 Hz (1) | Up to 150' (45 m) using shielded twisted pair STP or XTP DTP 24 cable
Using 1 coupler with 3' (0.9 m) to 9' (2.7 m) patch cable
Using 2 couplers with two 3' (0.9 m) (max) patch cables (each patch cable cannot
exceed 3')
Using two punch downs with two 3' (0.9 m) to 9' (2.7 m) patch cables |
| 4K/UHD@ 60 Hz (2) | Up to 175' (53 m) using shielded twisted pair STP or XTP DTP 24 cable w/ no couplers |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) |
| Signal Transmission Distance (using XTP DTP 22 cable) | |
| 1080p @ 60 Hz | Up to 330' (100 m) using XTP DTP 22 cable |
| 4K/UHD @ 30 Hz | Up to 330' (100 m) using XTP DTP 22 cable |
| 4K/UHD@ 60 Hz (1), (2) | Up to 330' (100 m) using XTP DTP 22 cable
Using 1 coupler with 3' (0.9 m) to 16' (4.9 m) patch cable
Using 2 couplers with 4' (1.2 m) (max) patch cables (each patch cable cannot
exceed 4')
Using two punch downs with 3' (0.9 m) to 8' (2.4 m) patch cables |
| Cable requirements | Solid conductor, 22 AWG or better |
| Cable recommendations | 500 MHz bandwidth, STP (shielded twisted pair) |
| NOTE | Extron XTP DTP 22 shielded twisted pair cable is strongly recommended for optimal performance.
(1) With coupler(s), (2) No couplers
|
|
|
| Communications |
|---|
| Control/Remote — Transmitter | |
| USB control port | 1 front panel, female USB type C |
| USB standards | USB 2.0, low speed |
| Program control | Extron Simple Instruction Set (SISTM)
Extron Product Configuration Software (PCS) |
| Control/Remote — External Device (pass-through, unidirectional or bidirectional) | |
| Serial control pass-through ports | 1 RS-232 3.5 mm 3-pole captive screw connector |
| Baud rate | 300 to 115200 baud |
| Protocol | 8 or 7 data bits
1 or 2 stop bits
No parity (default), even or odd parity |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd |
| NOTE | Protocol is mirrored between the connected DTP3 Rx endpoints and the "Over TP". Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP3 endpoints for control of remote sink or source devices. The "Over TP" port are simply pass-through connections to DTP endpoints. There is no RS-232 insertion from any DTP3 control port to the "Over TP" ports. |
|
|
| General |
|---|
| Power supply | External (included with Tx)
Input: 100 to 240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Device | 7.37 watts |
| Device and power supply | 8.62 watts |
| Remote power budget | 18.0 watts |
| NOTE | The receiver can be powered either locally by an external power supply or remotely by a transmitter on the other end of the twisted pair cable. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on top and sides |
| Thermal dissipation | |
| Device | 24.20 BTU/hr |
| Device and power supply | 28.48 BTU/hr |
| Mounting |
| Rack mount | Optional 1U high rack shelf |
| Furniture mount | Optional under-desk mount kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight | 0.6 lbs (0.27 kg) |
| Regulatory compliance | CE, C-tick, C-UL, UL, FCC Class A, ICES, VCCI
Complies with the appropriate requirements of RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%.
Specifications are subject to change without notice. |
|
| (6233-D8) |